收藏本站
NCP5006
PIN FUNCTION DESCRIPTION
Pin
1
Pin Name
V out
Type
POWER
Description
This pin is the power side of the external inductor and must be connected to the
external Schottky diode. It provides the output current to the load. Since the boost
converter operates in a current loop mode, the output voltage can range up to
+24 V but shall not extend this limit. However, if the voltage on this pin is higher
than the Over Voltage Protection threshold (OVP) the device comes back to
shutdown mode. To restart the chip, one must either send a Low to High
sequence on Pin EN, or switch off the V bat supply. A capacitor must be used on
the output voltage to avoid false triggering of the OVP circuit. This capacitor
should be 1.0 m F minimum. Ceramic type, (ESR <100 m W ), is mandatory to
achieve the high end efficiency. This capacitor limits the noise created by the fast
transients present in this circuitry. In order to limit the inrush current and to
operate with an acceptable start?up time, it is recommended to use any value
between 1.0 m F and 8.2 m F capacitor maximum. Care must be observed to avoid
EMI through the PCB copper tracks connected to this pin.
2
GND
POWER
This pin is the system ground for the NCP5006 and carries both the power and
the analog signals. High quality ground must be provided to avoid spikes and/or
uncontrolled operation. Care must be observed to avoid high?density current flow
in a limited PCB copper track. Ground plane technique is recommended.
3
FB
ANALOG INPUT
This pin provides the output current range adjustment by means of a sense
resistor connected to the analog control or with a PWM control. The dimming
function can be achieved by applying a PWM voltage technique to this pin (see
Figure 29). The current output tolerance depends upon the accuracy of this
resistor. Using a " 5% metal film resistor or better, yields a good enough output
current accuracy.
Note: A built?in comparator switch OFF the DC/DC converter if the voltage
sensed across this pin and ground is higher than 700 mV (typical).
4
EN
DIGITAL INPUT
This is an Active?High logic input which enables the boost converter. The built?in
pull down resistor disables the device when the EN pin is left open. The LED
brightness can be controlled by applying a pulse width modulated signal to the
enable pin (see Figure 31).
5
V bat
POWER
The external voltage supply is connected to this pin. A high quality reservoir
capacitor must be connected across Pin 1 and Ground to achieve the specified
output voltage parameters. A 4.7 m F/6.3 V, low ESR capacitor must be connected
as close as possible across Pin 5 and ground Pin 2. The X5R or X7R ceramic
MURATA types are recommended. The return side of the external inductor shall
be connected to this pin. Typical application will use a 22 m H, size 1008, to handle
the 1.0 to 100 mA max output current range. On the other hand, when the desired
output current is above 20 mA, the inductor shall have an ESR < 1.5 W to achieve
a good efficiency over the V bat range .
http://onsemi.com
3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP5030MTTXGEVB EVAL BOARD FOR NCP5030MTTXG
NCP5602EVB EVAL BOARD FOR NCP5602
NCP5603GEVB EVAL BOARD FOR NCP5603G HI FREQ
NCP5604AAGEVB EVAL BOARD FOR NCP5604AAG
NCP5608EVB EVAL BOARD FOR NCP5608
NCP5612GEVB EVAL BOARD FOR NCP5612G
NCV7680PWR22GEVB BOARD EVALUATION NCV7680
NDNA200 DIN-RAIL 35MM ALUMINUM 2M
相关代理商/技术参数
NCP5006SNT1 功能描述:LED照明驱动器 White LED Backlight RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5006SNT1G 功能描述:LED照明驱动器 White LED Backlight Boost RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5007 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Backlight LED Boost Driver
NCP5007/D 制造商:未知厂家 制造商全称:未知厂家 功能描述:Compact Backlight LED Boost Driver
NCP5007_06 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Backlight LED Boost Driver
NCP5007SNT1 功能描述:LED照明驱动器 White LED Backlight RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5007SNT1G 功能描述:LED照明驱动器 White LED Backlight Boost RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP5008 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators